Search found 9475 matches

by Shalmeneser
Mon Aug 08, 2022 5:01 pm
Forum: Forum Italiano
Topic: The GROOVE Effect
Replies: 23
Views: 4595

Re: The GROOVE Effect

* arc center = circle center : 8-)
* circle center with specific position : 8-)
* your picture Cattura.PNG : :shock:
by Shalmeneser
Mon Aug 08, 2022 4:33 pm
Forum: Help on using FreeCAD
Topic: Fillet covering entire face, rather than just specified edge
Replies: 11
Views: 1126

Re: Fillet covering entire face, rather than just specified edge

PartDesign_Fillet
Add a fillet
3. For a chain of tangentially connected edges only a single edge needs to be selected, the fillet will propagate along the chain.
by Shalmeneser
Mon Aug 08, 2022 4:12 pm
Forum: Help on using FreeCAD
Topic: helix go out of the allowed scope?
Replies: 10
Views: 1079

Re: helix go out of the allowed scope?

Coplanarity with the upper face.
by Shalmeneser
Mon Aug 08, 2022 10:05 am
Forum: Forum français
Topic: Un fichier spreadsheet avec annulation impossible
Replies: 22
Views: 1821

Re: Un fichier spreadsheet avec annulation impossible

Pour le crash pas obligatoirement, mais on peut se retrouver avec des problèmes plus tard dans la construction et la cause en est ce R=0.
On retrouve ce même problème avec des hélices soustractives qui touchent le bord (=coplanarité) et qu'il faut décaler.
by Shalmeneser
Mon Aug 08, 2022 9:48 am
Forum: Help on using FreeCAD
Topic: helix go out of the allowed scope?
Replies: 10
Views: 1079

Re: helix go out of the allowed scope?

Following the link in the red banner above, can you provide a file and your full version info ?

Without the file :
* the helix touches itself ?
* coplanarity ?
by Shalmeneser
Mon Aug 08, 2022 9:42 am
Forum: Help on using FreeCAD
Topic: sheetmetal created extentions can not be edited in sketch
Replies: 10
Views: 966

Re: sheetmetal created extentions can not be edited in sketch

For the 1st post, you can ask stupid questions :lol:
Can you share your full version info (follow the link in the banner above).
by Shalmeneser
Mon Aug 08, 2022 9:30 am
Forum: Forum français
Topic: Un fichier spreadsheet avec annulation impossible
Replies: 22
Views: 1821

Re: Un fichier spreadsheet avec annulation impossible

Pour le rayon impossible = 0, je ne vois pas pourquoi cela ne serait pas possible. Cela voudrait juste dire que dans ce cas, les trois points seraient alignés (les deux points de l'arc et le centre). En effet, en mathématiques on peut très bien avoir un rayon de longueur nulle qui du coup se confon...
by Shalmeneser
Mon Aug 08, 2022 9:18 am
Forum: Forum français
Topic: Un fichier spreadsheet avec annulation impossible
Replies: 22
Views: 1821

Re: Un fichier spreadsheet avec annulation impossible

Pour les infos de version, je n'accuse personne car le lien du Forum Français est maigre. Je parlais juste à Papyblaise. Cependant pour un premier post, cela peut-être utile de s'entrainer à donner sa version complète pour le jour où. Sinon le retour en arrière (Ctrl+Z) est inégal : pour certaines o...
by Shalmeneser
Mon Aug 08, 2022 9:11 am
Forum: Forum français
Topic: Un fichier spreadsheet avec annulation impossible
Replies: 22
Views: 1821

Re: Un fichier spreadsheet avec annulation impossible

Expression dans une cellule : Expressions/fr

Je ne suis pas sûr que if() existe, plutôt les expressions ternaires (problème de parenthèses !).