Be prepared then to face the issue to be not able to delete sketcher constraints then. (For me that would be even worse.)
Search found 52955 matches
- Fri Mar 29, 2024 9:23 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 192
- Fri Mar 29, 2024 9:18 am
- Forum: Forum in Deutsch
- Topic: stable- und Entwickler-Version parallel - gleiche Voreinstellungen?
- Replies: 2
- Views: 84
Re: stable- und Entwickler-Version parallel - gleiche Voreinstellungen?
Beim Snap-Paket weiß ich nicht, wie weit die Abschottung geht. Ansonsten ist es normal auf dieselbe config-Datei zuzugreifen. Sinnvoll musst Du selbst entscheiden.
Es kann allerdings auch mal Konflikte geben, wenn Eigenschaften dazukommen, also immer ein Backup für beide Versionen parat halten.
Es kann allerdings auch mal Konflikte geben, wenn Eigenschaften dazukommen, also immer ein Backup für beide Versionen parat halten.
- Fri Mar 29, 2024 8:44 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 192
- Fri Mar 29, 2024 8:21 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 192
Re: Can't create PD datums with a pre-selection?
I don't use PartDesign datums every day, but I was a bit surprised that they can't be created with a pre-selection. The error message is confusing: "There are no attachment modes that fit selected objects. Select something else." All pre-selections are simply ignored AFAICT. Or am I missi...
- Fri Mar 29, 2024 8:18 am
- Forum: Forum in Deutsch
- Topic: in Part Variante erstellen
- Replies: 2
- Views: 80
Re: in Part Variante erstellen
Dafür gibt es die Configuration tables.
- Fri Mar 29, 2024 6:32 am
- Forum: Help on using FreeCAD
- Topic: still struggling to understand the modeling process of freecad
- Replies: 12
- Views: 455
Re: still struggling to understand the modeling process of freecad
i draw a circle, hit P, then pull(extrude) the circle up and if i just type a number, lets say 6.5" it will extrude it to exactly 6.5 inches. Then if i hit F, and click the top surface it will offset the surface by what ever number and unit i type in. Now if i hit P again and grab the center o...
- Fri Mar 29, 2024 6:01 am
- Forum: Help on using FreeCAD
- Topic: Cutting out multiple objects with paths
- Replies: 2
- Views: 104
Re: Cutting out multiple objects with paths
There is no job in your model, so we don't know what you tried. - Note, that a pocket will fail, if the tool has exactly the diameter of the distance between the squares. - To get this done with an optimized path milling always from end to end, you may need further helper sketches and e.g. pretend t...
- Fri Mar 29, 2024 5:51 am
- Forum: UX/UI Design
- Topic: A new take on the UI. FreeCAD Nut.
- Replies: 121
- Views: 201385
- Fri Mar 29, 2024 5:47 am
- Forum: Forum in Deutsch
- Topic: Körper2 aus Körper1 stanzen boolsche Funtion
- Replies: 16
- Views: 1233
- Fri Mar 29, 2024 5:27 am
- Forum: Path/CAM
- Topic: FreeCAD CAM Tutorials on Youtube
- Replies: 6
- Views: 271
Re: FreeCAD CAM Tutorials on Youtube
Thanks for the information. I will look into those parts, especially the UC300ETH looks promising. Until now I only looked at the Mesa cards to retrofit a Maho from the 80's.